Front Wheel Drive (FWD) Bearing Remover and Installer Set

Used for the removal and installation of FWD bearings without the need to remove the vehicle's steering knuckle and strut assembly—no need to re-align the car afterward!

Slide Hammer and Puller Set

Ideal for a variety of pulling applications, including flange-type rear axles, most front-wheel drive hubs, dent pulling, and other press-fit parts (bearings, bushings, gears, pulleys, etc.).

Blind Hole Collet Bearing Race and Seal Puller Kit

Used for the removal of tight or jammed axles, bearings, and bushings without damaging the removed parts, using expandable collets and threaded screw adapters.

2/3 Jaw Reversible Gear Puller Set

Used for the removal of stubborn or stuck gears and pulleys. Reversible 4” and 6” jaws allow the puller to be used for both inside and outside pulls.

Radiator Coolant Pressure Tester

Used for precise testing of radiator pressure leakage. Pressure testing range: 0-35 PSI.

Exhaust Pipe Expander and Cutter Tool Set

Used for the replacement or repair of broken or dented exhaust pipes up to 3-1/2” in diameter. Includes a chain cutter for trimming pipes and a nut splitter for breaking rusted or corroded bolts.

Spindle Nut Socket Set

Used for the easy removal of hard-to-remove spindle nuts, with clearly labeled sockets both on the socket and on the blow-molded case.

Double Flaring Tool Adapter Set

Used for flaring a double or single flare in copper, aluminum, brass, magnesium, and soft steel brake line tubing.

NOTE: Not designed for use with stainless steel or other hardened steel materials.

Pneumatic One-Person Brake Bleeder Kit

Pneumatic tool for brake, clutch, and engine oil changes with automatic shut-off. Can be operated by one person.

Brake Piston Compression Tool

Used for compressing inner brake pads and resetting pistons.

Brake Caliper Hanging Tool

Used to hold brake calipers out of the way, reducing the possibility of damage to calipers, brake hoses, and other parts.

Master Tap and Die Set (SAE & Metric)

Used for hand threading and rethreading tasks across a wide range of applications, including auto repairs and metal fabrication. Can be used to cut new threads and chase or renew existing threads.

Diagnostic Scan Tool (OBD2 & EOBD)

Used to identify the causes of the check engine light (CEL), read and clear diagnostic trouble codes, view live data and hard memory data, check freeze frame, monitor I/M readiness, and collect vehicle information.

Timing Light

Used to check the engine's ignition timing. Tach range: 249-9,990 RPM; Advance (2 & 4 cycle): 0-90 degrees; Dwell (2-12 cylinders): 0-180 degrees; Voltage: 10-16 volts DC.

Car Jump Starter

Used for quickly jump-starting your car in the event of a dead battery.

Battery Charger and Maintainer

Used to charge car batteries. Includes overcharge protection, short-circuit protection, overload protection, and reverse polarity protection.

Digital Torque Wrench

Used to ensure the precise amount of torque is applied to a fastener via electronic sensors and audible alerts. Torque range: 12.5 - 250.7 ft-lbs; 17 - 340 Nm.

6" Neiko Digital Caliper

Used for precise and exact measurement needs. Measurement accuracy: 0.001” (0.02 mm).

Trim Removal Tools

Used for the seamless removal of exterior and interior car trims, moldings, wheel hubs, and door panels without causing damage to your car.

Exhaust Hanger Removal Pliers

Used to separate frame-mounted rubber supports from exhaust hanger brackets.

Under-Hood Light

Used ideally for under-hood work, vehicle maintenance, and various tasks where lighting is limited/blocked.

Torch Gun

Used for a wide range of applications, including industrial welding, brazing, soldering, heat shrinkage, and rust removal.

Heat Gun

Ideal for heat shrinking, shrinking wrap, heating PVC, electronics, removing paint, loosening rusted bolts, and other heating purposes.